Cricket Pitch Covers Guide: Choosing, Laying and Storing Covers
A practical club guide to cricket pitch covers: what area to protect, how to choose a system, lay and remove it safely, manage water and store covers without damage.

Choose cricket covers from the current competition requirement and the area that genuinely needs protection—not from sheet size alone. Plan drainage, handling routes, weights and dry storage before buying. Lay covers early with enough trained people, keep water away from the protected surface, and never drag pooled water across the pitch. Match officials and the ground authority control when covers are used during a match.
Covers are a ground system, not just a sheet
A waterproof sheet can keep direct rain off a pitch, but a working cover system also has to manage wind, pooled water, handling, run-up protection and storage.
Clubs often discover the hidden problems after purchase:
- the sheet is large but does not protect the required surrounds
- water runs underneath from a higher edge
- too few people can move it safely
- the cover is folded wet and grows mould
- loose ballast creates a fielding hazard
- the storage route crosses fences or narrow gates
- an improvised repair catches and tears during deployment
Start with the competition playing conditions and the site. The product decision comes later.
Check the current rules first
MCC Law 10 governs covering the pitch and makes the use of covers during a match a matter for the ground authority and umpires within the agreed arrangements. Competition playing conditions may add more exact requirements.
New Zealand Cricket’s first-class playing conditions have, for example, required full protection of the pitch, specified protection of the surrounds and included bowlers’ run-ups. Those dimensions are useful evidence of how extensive elite cover systems can be, but they are not a universal instruction for every community match.
Before specifying covers, obtain the current rules for the exact grade and ask:
- Must the whole pitch be covered or only the match strip?
- Are the pitch surrounds included?
- How far must cover extend on either side?
- Must bowlers’ run-ups be protected?
- When may covers be laid or removed?
- Who makes that decision once match control begins?
- Are hessian, scrim or heat-management covers required?
- Does the venue have its own turf-management plan?
Do not treat an old tournament handbook as current authority. Record the source and season on the club’s ground-equipment checklist.
Decide what needs protection
Measure from the pitch actually selected for the match. A multi-strip square changes the distance to the edge, drains and storage area.
Map five zones:
- Match pitch: the prepared strip between the wickets.
- Pitch surrounds: adjacent turf that can send water toward the strip.
- Square: the wider prepared block, where traffic and runoff must be controlled.
- Run-ups: the approach and delivery areas used by bowlers.
- Drainage and discharge: where water will go when the cover is deployed and lifted.
The covered area needs to be large enough for the requirement, but simply adding more sheet is not always safer. Every extra square metre adds weight, wind load, stored volume and handling effort.
Main cover-system types
| System | Best fit | Advantages | Limitations |
|---|---|---|---|
| Flat sheets | Small clubs, strip protection, flexible layouts | Lower initial cost; modular | Pooling, folding and manual handling need careful planning |
| Roll-on sheets | Clubs with clear storage and deployment route | Faster, tidier movement | Roller weight, width and storage clearance |
| Mobile dome or raised covers | Sites needing runoff away from the pitch | Reduces direct pooling on the protected area | Higher cost; wind and manoeuvring controls essential |
| Modular run-up covers | Supplementing the main pitch system | Targeted protection | Joins can admit or redirect water |
| Breathable or heat-management layer | Surface management under turf advice | Can moderate drying or heat | Not a rain cover unless specified as such |
There is no best system independent of the ground. A lightweight flat sheet may suit a small school strip; a busy club with limited volunteers may gain more from a system that can be deployed quickly and consistently.
Specify the material and construction
Ask a supplier for the complete specification, not just overall dimensions.
Check:
- finished width and length
- fabric mass per square metre
- waterproofing and seam construction
- ultraviolet resistance
- reinforcement at edges, handles and tow points
- water absorption
- temperature range
- repair method and compatible patch material
- warranty conditions
- expected packed or rolled dimensions
- total dry weight and estimated wet handling weight
A cover can remain waterproof in its main panel while failing at seams, eyelets or abrasion points. Reinforcement should match the way the club will move and secure the system.
Bright or contrasting colours can help ground staff see folds and edges in poor weather. Colour alone, however, does not make a cover safe or easy to handle.
Understand slope and water movement
Water follows the lowest path. Before laying a cover, observe the square in rain if possible and note:
- the natural fall of the ground
- low points where a sheet will pool
- drains and whether they are clear
- uphill areas that can send water beneath the cover
- where pumped or swept water can be discharged
- whether runoff would enter another pitch, path or spectator area
Lay and tension the cover only in the way the manufacturer and ground plan allow. Improvised ridges, frames or heavy objects can introduce new hazards or damage the turf.
Do not empty a pool by lifting one edge and sending the water across the protected pitch. Move water toward an approved safe discharge point with the correct equipment and enough people to retain control.
Plan manual handling before purchase
A large wet cover is heavy, awkward and affected by wind. The safe crew size depends on the system, weight, route, weather and training—not on a generic number.
Complete a manual-handling assessment that covers:
- total dry and wet weight
- number and position of handles
- pushing, pulling, rolling and lifting actions
- ground gradients and slippery areas
- gates, corners and storage thresholds
- wind exposure
- communication and one-person command
- escape paths if the cover moves unexpectedly
- how deployment stops when control is lost
Children should not be used to make up a cover crew. Nor should one grounds volunteer attempt a large deployment alone because rain has arrived quickly.
Prepare a deployment route
Walk the path from storage to the pitch.
Remove or control:
- boundary rope and flat markers
- advertising boards
- practice stumps and balls
- benches, bags and drink crates
- cable covers
- open gates
- sprinkler caps or raised service points
- vehicles and trailers
- people who are not part of the crew
If the cover uses wheels or a roller, confirm the route has enough width, turning radius and load-bearing surface. A stored system that cannot get through its gate at speed is not an emergency system.
Laying flat covers
Follow the product instructions and club procedure. A typical controlled method is:
- stop play or ground work under the responsible official’s direction
- clear the deployment path and landing area
- inspect the cover for tears, tangled handles and loose fittings
- assign one crew leader and positions before moving
- orient the cover so seams and runoff work with the ground plan
- unroll or unfold progressively, keeping people on the agreed side
- smooth large trapped folds without stepping on vulnerable turf unnecessarily
- secure the system using approved, low-profile methods
- inspect the perimeter for channels that may direct water underneath
- keep the area controlled while weather and water load change
Never use loose bricks, metal stakes or other hard improvisations around a fielding or walking area. Approved ballast must be stable, visible and placed as the system requires.
Wind changes everything
A broad sheet can behave like a sail. A deployment that is manageable in still air can become uncontrollable in a gust.
Before moving a cover:
- check current conditions and the site’s wind exposure
- use the required crew and agreed commands
- keep people away from a loose leading edge
- do not stand on or wrap limbs in ropes or handles
- stop if the sheet starts lifting beyond control
- secure stored sections so one gust cannot unroll them
If the manufacturer’s wind limit or club risk assessment says not to deploy, do not improvise around it.
Removing covers without undoing the protection
Removal is not simply deployment in reverse. Water on the sheet has to go somewhere.
- Confirm removal timing with the ground authority or umpires.
- Inspect for pooled water and identify the discharge route.
- Pump, sweep or siphon water using the approved equipment.
- Remove ballast and fittings into a container, away from the square.
- Fold or roll from the planned edge so residual water travels away from the pitch.
- Keep muddy footwear and wheels off the protected area where possible.
- Move the cover completely beyond player run-off and ground machinery routes.
- Inspect the pitch and surrounds before other preparation begins.
Dragging a dirty underside over the match strip can return water and debris to the surface the cover was meant to protect.
During-match responsibilities
Once a match is under official control, ground staff should not independently lay or remove covers just because conditions appear to change. The Laws and playing conditions allocate decisions to the ground authority and umpires.
Clubs should agree the communication chain before the toss:
- who watches the forecast and radar
- who can call the cover crew
- who confirms the umpires’ decision
- where the crew waits
- which entrance is kept clear
- how scorers and teams are told the ground is live again
Fast deployment depends more on preparation and communication than on people running with a sheet.
Run-up and surround protection
Protecting the strip while leaving the bowler’s landing or approach saturated may not save the match. If the playing condition or turf plan requires run-up covers, design them as part of the whole system.
Look closely at joins. A lap facing the wrong way can funnel water underneath. A raised join can also become a trip risk during removal or ground preparation.
Keep cover edges and equipment away from the agreed boundary and run-off area once play resumes.
Storage is part of cover life
Wet storage shortens cover life and makes the next deployment unpleasant and unreliable.
After use:
- remove standing water, mud, leaves and grass
- clean only with methods compatible with the fabric
- dry both sides before long-term packing
- inspect seams, handles and abrasion points
- complete repairs using the approved patch system
- roll or fold on the marked sequence
- label modular sections and their orientation
- store clear of rodents, sharp tools, fuel and direct heat
- keep rollers or trolleys secure from movement
The store needs enough space to access the cover without stacking heavy gear on top. If the club cannot dry a large sheet indoors, plan a safe outdoor drying method that does not block paths or expose it to uncontrolled wind.
Inspection and maintenance record
Create one record for each cover section.
| Field | Example detail |
|---|---|
| Asset ID | Main cover A, run-up cover north |
| Dimensions | Finished size, not ordered size |
| Material | Supplier and specification |
| Purchase date | Warranty reference |
| Inspection date | Before season, after major use |
| Damage | Seam split, puncture, handle wear |
| Repair | Patch type, date, person |
| Dry status | Confirmed before storage |
| Storage location | Bay, roller or rack |
| Next action | Repair, clean, replace or review |
Small tears should be dealt with before they extend during a rushed wet-weather deployment.
Buying comparison worksheet
Compare quotations on the same basis.
| Question | Supplier A | Supplier B | Supplier C |
|---|---|---|---|
| Compliant protected area | |||
| Dry weight / wet handling plan | |||
| Deployment crew and time | |||
| Wind operating guidance | |||
| Seams and reinforced points | |||
| Roller, trolley or pump included | |||
| Repair kit and spare parts | |||
| Warranty and exclusions | |||
| Packed dimensions | |||
| Delivered total cost |
Ask for operating instructions before accepting a quotation. They may reveal crew, storage or weather limits that change the real cost.
Common mistakes
Buying from pitch length alone
The required area may include surrounds and run-ups. Measure the actual site and check the competition rule.
Ignoring the water exit
A cover moves rain; it does not make rain disappear. Plan drainage and discharge before deployment.
Using improvised weights
Loose hard objects create hazards and can tear the sheet. Use the approved securement method.
Folding it wet
Persistent moisture encourages odour, staining, degradation and stuck surfaces. Dry and inspect before storage.
Leaving the crew decision until rain starts
Assign roles, route and commands before match day. A forecast is not the moment to invent the process.
Treating elite dimensions as universal
Representative conditions show what a high-level event may require. Community clubs must use the current rule for their own competition and venue.
Club cover checklist
Before the season
- Current competition requirements obtained
- Match pitch, surrounds, run-ups and drainage measured
- Deployment route and storage access checked
- Manual-handling and wind controls documented
- Covers, seams, handles, roller and pump inspected
- Crew trained and communication chain agreed
Before a match
- Forecast monitored by the nominated person
- Covers orientated and ready
- Drainage and discharge points clear
- Crew contact confirmed
- Boundary equipment and route hazards identified
- Umpires and ground authority briefed
After use
- Water and debris removed
- Both sides dried
- Damage recorded and repaired
- Sections rolled or folded in sequence
- Fittings counted and contained
- Store secured and accessible
Frequently asked questions
What size cricket pitch cover does a club need?
The size must come from the current competition requirement and the site plan. It may need to protect the pitch, surrounds and run-ups. Measure the finished coverage, allowing for joins and the way water will leave the system.
Can a tarpaulin be used as a cricket cover?
A tarpaulin may shed rain, but it is not automatically suitable for seam strength, handling, wind, drainage or turf management. The ground authority should assess the whole system and the playing condition.
Should covers be removed as soon as rain stops?
Not automatically. During a match, the decision belongs to the responsible officials under the Laws and playing conditions. Water load, surface conditions and safe handling also matter.
How should covers be dried?
Remove water and debris, expose both sides using a controlled method, and follow the manufacturer’s cleaning and drying advice. Keep the sheet away from public paths and uncontrolled wind.
How many people should move a cover?
There is no safe universal number. It depends on dry and wet weight, system design, route, slope, wind and training. Use the manufacturer guidance and the club’s manual-handling assessment.
Sources and further reading
- MCC: The Laws of Cricket
- MCC: 2017 Code, 4th Edition 2026
- New Zealand Cricket playing conditions and resources
- New Zealand Cricket 2022–23 Playing Conditions: Law 10 example
- CricketWise boundary rope set-up guide
Use the current competition playing conditions, venue procedures, turf advice and cover manufacturer’s instructions. Older playing conditions are cited only as a documented example of how coverage requirements can be specified.